Skip to article
AHFE AHFE Discoveries AHFE International Open Access Journal
AHFE OPEN ACCESS OPEN ACCESS CONFERENCE PROCEEDINGS PAPER

Anthropometric characterization of Campeche's population

1 Autonomous University of Ciudad Juarez, Ciudad Juarez, Chihuahua 32584, Mexico; Calkini Superior Institute of Technology, Calkini, Campeche 24900, Mexico ↗
2 Autonomous University of Ciudad Juarez, Ciudad Juarez, Chihuahua 32584, Mexico ↗
3 Autonomous University of Baja California, Ensenada, Baja California 22860, Mexico ↗
Publication year
Digital Object Identifier10.54941/ahfe1003431

Abstract

Anthropometry is an important branch of ergonomics that deals with body measurements, particularly measurements of body size, shape, strength, mobility, flexibility, and work capacity. Reliable anthropometric data and technical procedures of ergonomics can be powerful tools to optimize the design of products to fit human dimensions. However, in Mexico, there is a scarcity of this type of data, particularly in the state of Campeche. This study aims to characterize the anthropometry of the economically active population in the northern part of the state of Campeche by creating an anthropometric chart for the design of adequate workstations and workspaces. The study was conducted with a sample of 382 subjects aged between 15 and 65 years, and 46 structural anthropometric dimensions and weights were taken and collected following the protocols most commonly used among experts in anthropometric and ergonomics. Data were analyzed to determine mean and standard deviation for all anthropometric dimensions. In conclusion, an anthropometric chart was developed to describe the characteristics of the economically active population as a priority for the manufacturing and service industries.

INTRODUCTION

Several studies have reported an increase in the prevalence of musculoskeletal problems in the general and working population in both developed and deve- loping countries (Buckle and Devereux, 2002; Colombini and Occhipinti, 2006; Ahacic and Kåreholt, 2010; Hagen et al., 2011; Öztürk and Esin, 2011; Nazari et al., 2012; Widanarko et al., 2014; Dianat et al., 2015; Organización Mundial de la Salud, 2021). Other researchers have also reported a high rate of occupational injuries due to inadequate equipment design and have pro- posed the analysis of anthropometric characteristics to improve safety and prevent workplace injury (Brki´c, Klarin and Brki´c, 2015; Sutalaksana and Widyanti, 2016). The prevention of MSDs is, therefore, one of the most important factors that can have a major impact on improving productivity and promoting occupational health and safety (Kogi et al., 2003).

Ergonomics has as its main objective the adaptation of tasks, spaces, and tools to the workers, and likewise, of products to the users. (Pheasant and

© 2023. Published by AHFE Open Access. All rights reserved. 706

Anthropometric Characterization of Campeche’s Population 707

Haslegrave, 2016). Designers of many products, environments, and systems must take into account the size and physical shape of the intended user often referred to as designing for physical adaptation (Garneau and Parkinson, 2016), as the workplace must adapt to the body size and mobility of operators (Grandjean and Kroemer, 1997).

Anthropometric measurements are considered the starting point for the design and redesign of workstations, where ergonomic guidelines are to be applied and support research and applied for work with quantitative argu- ments. This implies a greater facility for the adaptation and modification of the working conditions where the worker works, thus improving productive performance and decreasing the possibility of generating a musculoskeletal disorder in the workers that work in the workstations. (López Acosta et al., 2019). This study’s anthropometric measurements can serve as a founda- tion for the ergonomic design of equipment, tools, and workstations that can make the workplace safer and more user-friendly. Small and medium- sized enterprises offer significant employment opportunities in industrially developing countries. Regarding the productive development generated in the northern part of the state of Campeche, 77% of the working-age population is engaged in retail trade activities, the manufacturing industry, mainly texti- les, and providing temporary accommodation services. (INEGI, 2020). This involves manufacturing processes with in-line flows, activities that demand handling loads, and arranging goods. This requires the design of workstati- ons and workspaces, which are established empirically or with the available spaces and resources without performing an analysis of the needs of the population that uses them, so the adoption of a system of anthropometric measurements of these sectors, to use in the design of workstations, would generate many benefits and would be a factor of optimization in the methods and work processes, in addition to adjusting the workstations to the physical characteristics of the operators working in these sectors.

Therefore, anthropometric investigations can provide essential data for the design of ergonomic equipment, tools, products, or environments, and thus may have significant potential for improving work efficiency, productivity, ease of use, fit, comfort, and safety (Hanson et al., 2009; Kushwaha and Kane, 2016). The objective of this research is to develop an anthropometric chart that characterizes the economically active population of Campeche, making it the first anthropometric measurement in the State of Campeche, which is considered a significant contribution to the workforce in the area.

METHODOLOGY

Determination of the Sample According to the latest National Survey of Population and Housing, the economically active population reported in the Northern Zone of the State of Campeche, comprising the municipalities of Calkiní, Hecelchakán, and Tenabo is 66,571 people, of which 33,880 are women and 31,802 are men (INEGI, 2020).

Based on this information, it was determined that the sample size with a confidence level of 95% and an expected error of 5% for a population of 66,571 is 382.

Determination of the Anthropometric Measurements to be Included in the Study The following structural anthropometric dimensions were determined to have a database that allows the design of workstations, tools, and machinery according to the main economic activities carried out in the region.

Standing dimensions: Height, maximum vertical reach, eye height, shoul- der height, elbow height, hip height, knuckle height, toe height, knee height, upper limb length, shoulder-grip length, maximum lateral reach with the elbow at 90

  • with grip, maximum lateral reach with the elbow at 90
  • without grip, wingspan, elbow span, chest depth, abdominal depth.

Seated dimensions: Height in a seated position, height to eyes seated posi- tion, the height of shoulder in a seated position, height for elbow rest, height subscapularis height, the height of iliac crest, thigh thickness, gluteal-knee length, gluteal-popliteal length, popliteal height, knee height, shoulder width (bideltoid), shoulder width (biacromial), hip width, head length, head width, elbow length to fingertips, shoulder-elbow length, functional grip reach, hand length, palmar length, palm width, hand width, wrist circumference, wrist thickness, wrist width, grip circumference/hand grip diameter, foot length, foot width.

Measuring Instruments For the measurement of body weight and the descriptive dimensions of body composition consisting of body fat percentage, muscle mass percentage, and bone density, bioimpedance was selected as the measurement method because it is considered a safe, cheap, accurate, and non-invasive method that pro- vides data on a person’s body composition (García-Soidan et al., 2014; Gutiérrez and Beneit, 2011; Ortega González et al., 2018; Quintero Alarcón et al., 2022). A specialized digital scale H.U.T. model HBBSVD-2559 was used, which has a Strain-Gauge system with 4 high-precision sensors to mea- sure body fat and water, muscle mass, bone density, the minimum required kilocalories, and body mass index. The maximum capacity of the scale is 180 kg with a 100 g measurement division. The other structural anthropometric dimensions were measured with a complete ErgoMeasure anthropometer kit, consisting of a 2010 mm por- table stadiometer, a 700 mm large vertical straight-branch anthropome- ter, a 500 mm medium straight-branch anthropometer, a 250 mm small straight-branch anthropometer for hand measurements, a cone for measu- ring grip diameters, all with an accuracy of ±1 mm. In addition, a 150 mm flexible tape measure, a 300 mm digital tape measure, and a height-adjustable bench.

Data Collection The sample was selected randomly using the Catalog of Localities of the Support System for the Planning of the Program for the Development of Priority Zones Planning Support System was used to identify the total number of localities in each of the municipalities to be studied. With this informa- tion, a basic ballot box model was used to select the localities where the

Anthropometric Characterization of Campeche’s Population 709

measurements were taken for each of the municipalities. Once the locali- ties were selected, the participants determined in the sample were selected through the quota sampling principle. Therefore, by knowing and having established the criteria of the municipality, gender, and age ranges, it was feasible to select individuals at the discretion of the researcher, following the quota sampling method.

Once the dimensions and measurements for the research were determined, a formal request was made to the Ethics and Research Committee of the Autonomous University of Ciudad Juarez for the evaluation of the scienti- fic, medical, ethical and legal aspects of the research project, obtaining its authorization.

During the measurement session, the purpose of the research was briefly explained to each participant and he/she was asked if he/she wished to par- ticipate in the research. The participants’ signatures were obtained on the informed consent form and an interview was conducted to collect basic soci- odemographic information, including gender, place of origin, date of birth, age, current employment status (employed or unemployed), sector of employ- ment (primary, secondary, tertiary), work activity, family relationship (in the case of relatives).

Once the sociodemographic information was collected, height was measu- red with an ErgoTech México ErgoMeasure portable stadiometer. Following the protocol applied by Hernandez-Arellano et al., (2016). The digital scale was configured according to height, gender, and age, asking the subject to step on the scale without shoes, jewelry, or watches that could interfere with the reading, with arms resting on the sides of the body and the head pla- ced in the Frankfort plane and proceeded to measure weight, muscle mass percentage, body fat percentage, dehydration percentage, and bone density.

Subsequently, the remaining anthropometric measurements were taken according to accepted anthropometric protocols, taking two independent measurements for each dimension for each subject. If the difference between the two measurements exceeded the acceptable level, a third measurement was taken to ensure the accuracy of the records. (Hernandez and Gómez Bull, 2016; López Acosta et al., 2019).

Information Processing For the statistical processing of the data, mean and standard deviation were calculated following the methods used by Avila-Chaurand, Prado-León and González-Muñoz (2007); Hernández Flores (2015); and Vázquez Salinas, Ibarra Mejía and Guerra Jaime (2016).

The information was collected in a Microsoft Excel spreadsheet and subsequently processed generating the mean and standard deviation for each dimension.

RESULTS

The following tables show the data of body weight and the descriptive dimen- sions of body composition consisting of body fat percentage, muscle mass percentage and bone density, as well as the 46 structural dimensions of the sample of 382 subjects (275 men and 107 women) from the northern part of the state of Campeche, Mexico.

Continued

Men 15-29 Men 30-49 Men 50-65

Table 1. Anthropometric data of men from 15 to 65 years of age (prepared by the authors).

Table available in the original PDF paper.

Dimension (cm) Mean SD Mean SD Mean SD

Body weight (kg) 74.63 15.07 78.70 14.70 74.54 14.47 Body fat percentage 23.60 5.75 28.99 5.25 29.39 5.02 Muscle mass percentage 36.98 3.52 33.56 3.09 33.24 2.91 Bone density (kg) 3.01 0.19 3.09 0.18 3.08 0.18 Height 165.64 6.53 160.39 6.73 158.13 6.03 Max vertical reach 211.07 8.14 204.69 9.24 202.77 8.88 Eye height 155.92 6.93 150.20 6.47 147.97 5.70 Shoulder height 139.12 6.41 135.65 7.87 132.53 6.00 Elbow height 104.27 5.80 101.31 4.54 99.66 4.99 Hip height 96.00 4.77 90.77 4.76 91.74 3.93 Knuckle height 72.06 3.41 70.77 4.38 69.84 3.58 Toe height 62.27 3.23 61.91 3.80 59.95 3.35 Knee height 51.62 4.71 49.37 2.57 49.90 3.85 Upper limb length 83.16 4.29 81.14 4.28 80.79 4.21 Shoulder-grip length 71.97 3.76 70.46 4.47 70.35 3.89 Max lateral reach elbow 90

  • with grip 36.55 1.85 35.43 1.70 35.65 1.73 Max. lateral reach elbow 90
  • without grip 46.66 2.07 45.44 1.93 45.50 1.92 Wing span 173.50 7.45 168.87 7.69 166.46 8.64 Elbow span 89.99 5.02 88.19 4.25 85.93 4.81 Chest depth 22.84 2.42 23.98 2.42 23.91 2.22 Abdominal depth 23.68 3.84 27.09 3.78 28.33 3.70 Height Seated Position 85.13 4.68 83.35 5.65 81.11 3.39 Height to Eyes Seated Position 74.44 4.10 71.67 4.30 69.42 6.31 Height of Shoulder in Seated Position 57.49 7.88 56.49 6.85 54.23 2.36 Height for Elbow Rest 20.70 3.07 21.23 2.96 20.22 2.65 Subscapularis Height 45.23 3.50 44.48 2.96 42.88 3.46

Anthropometric Characterization of Campeche’s Population 711

Men 15-29 Men 30-49 Men 50-65

Table 1. Continued.

Table available in the original PDF paper.

Dimension (cm) Mean SD Mean SD Mean SD

Height of Iliac Crest 17.13 1.87 15.72 1.51 15.31 1.39 Thigh Thickness 15.09 2.24 15.19 1.98 14.35 2.18 Gluteal-Knee Length 59.26 3.40 58.17 2.68 57.34 3.50 Gluteal-Popliteal Length 47.74 2.83 45.79 2.59 45.58 3.48 Popliteal Height 42.33 3.09 39.97 2.31 40.28 3.16 Knee Height 52.22 3.20 50.39 2.28 49.52 4.55 Width Bideltoid 47.60 3.67 48.79 3.78 48.32 3.65 Width Biacromial 41.24 2.61 40.86 2.10 41.17 2.30 Hip Width 41.39 3.92 42.38 3.13 40.96 3.15 Head Length 19.14 0.79 19.22 0.87 20.42 6.27 Head Width 16.75 0.63 17.39 4.10 16.58 0.89 Elbow Length to Fingertips 46.71 2.44 45.19 2.66 44.70 3.27 Shoulder-Elbow Length 36.23 4.21 35.20 5.66 35.12 4.67 Functional Grip Reach 171.29 7.82 165.58 8.46 165.32 7.14 Hand Length 18.61 0.82 18.00 0.91 18.22 0.97 Palm Width 9.88 0.59 9.93 0.54 9.99 0.56 Hand Width 8.22 0.65 8.26 0.61 8.42 0.36 Palmar Length 10.67 0.51 10.53 0.63 10.47 0.50 Wrist Circumference 18.31 1.27 18.68 1.15 18.87 1.02 Wrist Thickness 6.17 0.41 6.28 0.43 6.33 0.38 Wrist Width 4.55 0.44 5.39 5.70 4.63 0.36 Hand Grip Diameter 42.79 3.30 39.16 3.54 38.85 3.22 Foot Length 25.63 1.05 24.67 1.19 25.03 1.28 Foot Width 10.11 0.60 9.87 0.48 10.06 0.66

Continued

Women 15-29 Women 30-49 Women 50-65

Table 2. Anthropometric data of women from 15 to 65 years of age (prepared by the authors).

Table available in the original PDF paper.

Dimension (cm) Mean SD Mean SD Mean SD

Body weight (kg) 60.08 12.24 69.42 12.34 77.13 13.33 Body fat percentage 26.53 5.13 34.79 6.41 40.38 6.44 Muscle mass percentage 34.65 2.34 30.63 2.91 28.22 2.78 Bone density (kg) 2.10 0.10 2.12 0.06 2.16 0.07 Height 154.12 6.48 148.86 5.12 147.44 4.60 Max vertical reach 194.22 9.73 187.29 7.52 185.37 6.66 Eye height 143.86 6.54 140.18 6.87 137.66 7.11 Shoulder height 127.22 9.71 124.35 4.44 123.46 4.21 Elbow height 95.98 4.93 94.50 3.50 93.59 3.42 Hip height 92.14 4.86 88.08 4.32 87.80 3.80 Knuckle height 67.89 3.79 67.15 3.28 66.97 2.99 Toe height 59.07 3.67 58.60 4.36 57.94 2.85 Knee height 47.71 3.36 46.07 2.75 46.08 2.51 Upper limb length 76.04 3.70 74.31 3.07 74.83 3.29 Shoulder-grip length 66.17 3.69 64.68 3.11 65.33 2.85 Max lateral reach elbow 90

  • with grip 33.80 1.96 33.18 1.53 33.70 1.97 Max. lateral reach elbow 90
  • without grip 42.89 1.92 42.04 1.60 42.50 2.00 Wing span 158.16 7.50 153.47 6.43 153.49 6.16 Elbow span 82.70 4.17 81.89 12.31 80.27 3.20 Chest depth 20.14 1.93 22.36 2.33 23.35 1.97 Abdominal depth 22.15 3.70 27.24 3.69 30.98 4.20 Height Seated Position 80.63 3.57 78.50 3.11 77.68 2.99 Height to Eyes Seated Position 69.79 3.47 67.96 3.01 66.91 4.08 Height of Shoulder in Seated Position 52.56 3.01 52.57 2.30 52.64 2.65

Anthropometric Characterization of Campeche’s Population 713

Women 15-29 Women 30-49 Women 50-65

Table 2. Continued.

Table available in the original PDF paper.

Dimension (cm) Mean SD Mean SD Mean SD

Height for Elbow Rest 20.23 5.80 21.39 2.35 20.84 2.54 Subscapularis Height 41.68 3.41 41.13 2.32 41.22 2.93 Height of Iliac Crest 17.81 2.22 17.22 1.95 17.73 1.90 Thigh Thickness 14.05 1.84 14.61 1.72 15.56 2.17 Gluteal-Knee Length 56.14 2.98 55.04 2.38 55.89 3.35 Gluteal-Popliteal Length 45.81 2.65 44.66 2.55 44.77 2.72 Popliteal Height 38.52 2.06 37.24 3.58 36.09 2.47 Knee Height 48.45 2.44 46.80 2.64 46.40 2.68 Width Bideltoid 43.57 3.84 46.52 3.79 48.16 3.71 Width Biacromial 36.67 2.46 37.16 2.18 37.98 2.15 Hip Width 40.91 3.92 43.63 4.18 45.24 5.04 Head Length 18.64 0.79 18.34 0.95 18.39 0.74 Head Width 16.28 0.61 16.25 0.64 16.22 0.93 Elbow Length to Fingertips 43.11 1.94 42.00 1.68 42.04 2.63 Shoulder-Elbow Length 33.76 3.55 31.82 1.89 32.08 2.58 Functional Grip Reach 157.62 12.94 154.09 4.80 152.68 5.80 Hand Length 17.07 0.76 16.64 0.70 16.48 0.89 Palm Width 8.74 0.54 8.79 0.49 8.87 0.67 Hand Width 7.28 0.46 7.27 0.40 7.38 0.55 Palmar Length 9.79 0.50 9.65 0.53 9.63 0.43 Wrist Circumference 16.61 1.21 17.55 1.26 18.35 1.55 Wrist Thickness 5.57 0.36 5.91 0.47 6.15 0.51 Wrist Width 4.02 0.38 4.30 0.39 4.53 0.40 Hand Grip Diameter 39.86 2.88 37.19 2.38 37.25 2.23 Foot Length 23.12 1.18 22.77 0.95 23.36 1.13 Foot Width 8.97 0.55 9.21 0.58 9.54 0.74

CONCLUSION

One of the key benefits of reliable anthropometric information is the ability to optimize product design and reduce the risk of injuries and disorders. By considering the physical characteristics of the target population, product desi- gners can create products that are better suited to the intended user, reducing the likelihood of injury or discomfort associated with the use of the product. In the case of this study, the design of an anthropometric chart that describes the characteristics of the economically active population in the northern part of the state of Campeche represents an important step in reducing the risk of workplace injuries and musculoskeletal disorders.

In addition to improving product design, anthropometric information can also be used to evaluate the ergonomics of existing products and worksta- tions. By comparing the physical dimensions of the user to the dimensi- ons of the product or workstation, ergonomists can identify areas where adjustments may be necessary to improve the fit and comfort of the product.

Anthropometric information can also be used to guide the selection of personal protective equipment, such as gloves, safety glasses, and protective clothing. By considering the physical characteristics of the user, ergonomists can choose equipment that provides adequate protection while also ensuring a comfortable fit. This is particularly important in industries where workers are required to use personal protective equipment on a regular basis, such as construction, manufacturing, and healthcare.

It can be concluded that the design of an anthropometric chart describing the characteristics of the economically active population, which considers the main measures used in the design of workstations and workspaces under ergonomic guidelines, continues to be a priority for the manufactu- ring and service industries, since it is possible to reduce the risk of injuries or musculoskeletal disorders derived from the adoption of inadequate postures.

ACKNOWLEDGMENT

The authors are grateful for the financial support of the National Council of Science and Technology (CONACYT) for this research, with the grant 659427.

REFERENCES

Ahacic, K. and Kåreholt, I. (2010) ‘Prevalence of musculoskeletal pain in the general Swedish population from 1968 to 2002: age, period, and cohort patterns’, Pain, 151(1), pp. 206–214. Avila-Chaurand, R., Prado-León, L. R. and González-Muñoz, E. L. (2007) Dimensiones antropométricas de población latinoamericana. Segunda. Edited by Centro Universitario de Arte Arquitectura y Diseño and Centro de Investigaciones en Ergonomía. Guadalajara: Universidad de Guadalajara. Brki´c, V. K. S., Klarin, M. M. and Brki´c, A. D. (2015) ‘Ergonomic design of crane

cabin interior: The path to improved safety’, Safety science, 73, pp. 43–51. Buckle, P. W. and Devereux, J. J. (2002) ‘The nature of work-related neck and upper limb musculoskeletal disorders’, Applied ergonomics, 33(3), pp. 207–217.

Anthropometric Characterization of Campeche’s Population 715

Colombini, D. and Occhipinti, E. (2006) ‘Preventing upper limb work-related musculoskeletal disorders (UL-WMSDS): New approaches in job (re) design and current trends in standardization’, Applied ergonomics, 37(4), pp. 441–450. Dianat, I. et al. (2015) ‘Association of individual and work-related risk factors with

musculoskeletal symptoms among Iranian sewing machine operators’, Applied ergonomics, 51, pp. 180–188. Garneau, C. J. and Parkinson, M. B. (2016) ‘A survey of anthropometry and physical accommodation in ergonomics curricula’, Ergonomics, 59(1), pp. 143–154. Grandjean, E. and Kroemer, K. H. E. (1997) Fitting the task to the human: a textbook

of occupational ergonomics. CRC press. Hagen, K. et al. (2011) ‘Increasing prevalence of chronic musculoskeletal complaints.

A large 11-year follow-up in the general population (HUNT 2 and 3)’, Pain Medicine, 12(11), pp. 1657–1666. Hanson, L. et al. (2009) ‘Swedish anthropometrics for product and workplace design’, Applied ergonomics, 40(4), pp. 797–806. Hernández Flores, G. (2015) Uso de medidas antropométricas para el diseño

de estaciones de trabajo enfocado a operadoras de las industrias de la Zona Metropolitana de Guadalajara. Available at: https://ciateq.repositorioinstituc ional.mx/jspui/bitstream/1020/161/1/Uso de medidas antropometricas para el diseño.pdf. Hernandez, J. L. and Gómez Bull, K. G. (2016) Manual de prácticas de antropometría, biomecánica y fisiología. 1a Edición. Edited by Universidad Autónoma de Ciudad Juárez. Ciudad Juárez, Chihuahua. Hernandez-Arellano, J. L. et al. (2016) ‘Anthropometrics of University Students

in Northern Mexico’, Open Journal of Safety Science and Technology, 06(04), pp. 143–155. doi: 10.4236/ojsst.2016.64011. INEGI (2020) Censo de Población y Vivienda 2020 - Cuestionario Básico. Available at: https://www.inegi.org.mx/programas/ccpv/2020/#Microdatos. Kogi, K. et al. (2003) ‘Low-cost work improvements that can reduce the risk of

musculoskeletal disorders’, International Journal of Industrial Ergonomics, 31(3), pp. 179–184. Kushwaha, D. K. and Kane, P. V (2016) ‘Ergonomic assessment and workstation design of shipping crane cabin in steel industry’, International journal of industrial ergonomics, 52, pp. 29–39. López Acosta, M. et al. (2019) Antropometría para el diseño de puestos de tra-

bajo. Primera. Edited by E. ITSON. Ciudad Obregón: Instituto Tecnológico de Sonora. Available at: https://www.itson.mx/publicaciones/Documents/ingytec/lib ro antropometri’a.pdf. Nazari, J. et al. (2012) ‘Working conditions in carpet weaving workshops and muscu-loskeletal complaints among workers in Tabriz-Iran’, Health promotion perspectives, 2(2), p. 265. Organización Mundial de la Salud (2021) Trastornos musculoesqueléticos, Datos y

cifras. Alcance y Magnitud. Available at: https://www.who.int/es/news-room/fac t-sheets/detail/musculoskeletal-conditions (Accessed: 22 November 2021). Öztürk, N. and Esin, M. N. (2011) ‘Investigation of musculoskeletal symptoms and ergonomic risk factors among female sewing machine operators in Turkey’, International Journal of Industrial Ergonomics, 41(6), pp. 585–591. Pheasant, S. and Haslegrave, C. M. (2016) Bodyspace. Anthropometry, ergonomics

and the design of work. 2

  • . Edited by T. & F. Group. CRC Press.

Sutalaksana, I. Z. and Widyanti, A. (2016) ‘Anthropometry approach in workplace redesign in Indonesian Sundanese roof tile industries’, International Journal of Industrial Ergonomics, 53, pp. 299–305. Vázquez Salinas, A. G., Ibarra Mejía, G. and Guerra Jaime, A. (2016) ‘Perfil

antropométrico de la población del estado de Chihuahua’, Cultura Científica y Tecnológica, (56), pp. 198–207. Available at: https://erevistas.uacj.mx/ojs/index. php/culcyt/article/view/814/777. Widanarko, B. et al. (2014) ‘The combined effect of physical, psychosocial/organisational and/or environmental risk factors on the presence of work-related musculoskeletal symptoms and its consequences’, Applied ergonomics, 45(6), pp. 1610–1621.

Cover of the proceedings volume Ergonomics In Design

Explore the complete digital volume

Ergonomics In Design

Read this individual research paper free through the original publisher, or explore the full digital proceedings book.

ISBN 978-1-958651-53-7

Explore this ISBN in the AHFE Bookstore Listed in the July 2026 bookstore catalogue; search by ISBN to confirm current availability · Digital book purchase optional

Explore Related Research

Related research 8 matches

More papers from this volume

← Back to Research ExplorerBrowse the full library →