INTRODUCTION
Most of the contemporary work setups require the workers to perform seden- tary work and remain in seated position for prolonged periods of time. The unfavourable effects of attaining these static and uncomfortable positions while working include physical conditions like incidence of musculoskeletal disorders, psychological conditions like aversion from work and cognitive conditions like lack of concentration and focus at work. Exposure to such work conditions leads to decline in overall performance of the workers as well as lowered sense of general wellbeing. Continuous interaction with machi- nes especially VDTs is a common work practice in almost every work setup. General ergonomic solutions can be derived by a comprehensive understan- ding of the physical and cognitive aspects of user-machine interface at work, workplace design and workspace layouts, physical environment, psycholo- gical environment and the attributes of job design. Flexible workstations like sit-stand workstation to decrease the pressure of continuous sitting have been tested in different studies in different time frames, but workers eventu- ally ended up performing the work throughout the day sitting for prolonged
© 2023. Published by AHFE Open Access. All rights reserved. 231
periods and rarely using the standing workstation, which justifies Bridger (2019) quoting Sitting is the new smoking. The posture that needs to be acquired at work is determined by the design of displays of the machine the worker is interacting with, the control mechanisms that need to be operated and the panel layouts. Practically, the nature of work is difficult to change, but appropriate measures can be taken to reduce the strain imposed on the workers while being seated at work for prolonged hours. The National Insti- tute of Occupational Safety and Health estimates that more than fifty percent (50%) of the workforce in the United States experiences repetitive stress inju- ries, primarily back ailments (acute, chronic, and repeated) brought on by sitting for extended periods of time while performing a range of tasks.
An ergonomic seating design is one of the most practical solutions to the problem. Various studies have been conducted to develop such solutions, and some effective designs have been created to deal with the postural problems that arise due to constant need to sit at work. Various technology-based solu- tions have been devised till date for assessment of postural deviations at work so that corrective actions can be taken. The study, here, presents a compreh- ensive preventive and corrective measure to deal with such postural issues at work. The sensor based ergonomic cushion that can be used with any chair, does not only detect an awkward posture but also corrects it as soon as it is attained.
PAST WORKS Prommanon (2015) conducted a study to determine how a back care pillow (BCP) affected individuals with chronic non-specific low back pain in terms of discomfort, lumbar range of motion (LROM), and functional impairment (LBP) and concluded that BCP combined with physical therapy had better pain, lumbar ROM, and functional disability outcomes than physical the- rapy alone. Lee et al. (2018) developed a gel cushion made of thermoplastic styrene-ethylene/butylene-styrene elastomers to assess the impact of the gel cushion and found it to be very effective in managing back pain in profes- sional drivers. Chapman et al. (2006) developed a computerized system for cushion design and material testing by allowing the input of data on pro- trusions (small parts protruding from the major surface) and more latitude on the design of cushion systems. Kamara et al. (2019) developed a smart cushion integrated with e-textile pressure sensors to monitor activities on a chair including occupancy, sitting duration, and body posture and ori- entation. Luo et al. (2017) developed a smart cushion composed of three parts, pressure data acquisition module (internet of things), data receiving and processing module, data storage and analysis module and found out that the design was capable of the dynamic and real-time measurement of the pressure center in the sitting posture, and cumulative effect calculation. Makhsous et al. (2009) suggested that sitting with reduced ischial support and enhanced lumbar support results in reduced sitting load on the lumbar spine and reduces the lumbar muscular activity, which may potentially reduce sitting-related LBP.
Sensor Based Ergonomic Cushion for Posture Detection and Correction 233
DESIGN OF SENSOR BASED CUSHION People are prone to adopting awkward postures in order to adjust themse- lves for any working or resting position. This can be attributed to the natural capability of adaptation, which should not ideally exceed the prescribed limit. As a consequence of these unnatural postures, a host of musculoskeletal problems come into being. Keeping in mind, that it is quite difficult to train individuals to attain a posture as close to the natural curvature as possible, the design of the sensor based posture detector and corrector ergonomic cushion is proposed.
An ideal sitting posture requires the individual to maintain these gaps
- 1.5 to 3 cm between the cervical spinal bone and the chair - 1.5 to 3 cm between the thoracic spinal bone and the chair - 1.5 to 3 cm between the sacral spinal bone and the chair When a person is sitting in a chair in an optimal position, usually these gaps between the spinal column and the chair are observed.
- 25 to 30 cm between the cervical spinal bone and the chair - 7 to 12 cm between the thoracic spinal bone and the chair - 3-5 cm between the sacral spinal bone and the chair As the worker changes position to a more relaxed one, these gaps tend to change, altering the pressure experienced at different parts of the body. These gaps usually become:
- 2 to 3 cm between the cervical spinal bone and the chair - Approx. 1cm between the thoracic spinal bone and the chair - 12-20 cm between the sacral spinal bone and the chair Similarly, as different postures are acquired to suit the demands of the work or adjust to the design of furniture and equipment, these gaps change and undue postural deviations are observed. This calls for the seat cush- ion to accommodate the body providing it as much comfort as desired, and minimise the stress imposed on the spinal column. Usually, the conventio- nal design of the cushions is not suited to meet these requirements of the user and the user might thus be required to attain an awkward posture while remaining seated.
Typically a cushion for a work chair is 46–57 cm in height and 33–40 cm in width. An ergonomic sensor based cushion is developed here to create a solution for the attainment of unnatural postures at work or for rela- xation. The specific areas of the cushion bloom and sag once the sensor identifies the deviation from the natural posture and a microcontroller handles the operation of expansion and deflation of the cushion to cor- rect the posture. A smart printed flex sensor is deployed that provides the pressure readings which will provide instant activation to the part for support.
CONCLUSION
An ergonomic approach to designing of products used while performing dif- ferent types of tasks is the best way to deal with various situations leading to work related musculoskeletal disorders. Technology based designs are most sought out solutions to such problems nowadays. The modern work world mainly comprises activities that require prolonged sitting from the worker leading to attainment of unnatural awkward postures at work. The design of the sensor based ergonomic cushion presents a solution not just for identifi- cation and analysis of such awkward postures, but also for correction of the posture as soon as it deviates from the natural posture beyond the acceptable limit.
REFERENCES
Bridger, R. (2019). A Guide to Active Working in the Modern Office: Homo Sedens in the 21st Century (1st ed.). CRC Press. https://doi.org/10.1201/9780429021299 Chapman, R., Trost T., Cavlin S. System for cusghion design and testing. Packaging
Technology and Science, 2006 Vol 4, Issue 5/ p. 275–278, Wiley Online Library https://doi.org/10.1002/pts.2770040507 Kamara V., Nicholas P C., Cay G. Mankodiya K. Fine SJ., Design of a Smart Cushion Integrated with E-Textiles. 2019, The 16th IEEE-EMBS International Conference on Wearable and Implantable Body Sensor Networks (BSN’19)At: Chicago, IL Lee JW, Lim YH, Won YH, Kim DH. Effect of gel seat cushion on chronic low back pain in occupational drivers: A double-blind randomi- zed controlled trial. Medicine (Baltimore). 2018 Oct;97(40):e12598. doi: 10.1097/MD.0000000000012598. PMID: 30290629; PMCID: PMC6200541. Luo, S., Wang, Y., Gong, Y., Shu, G., Xiong, N. (2017). A Preliminary Study of Smart
Seat Cushion Design. In: Streitz, N., Markopoulos, P. (eds) Distributed, Ambient and Pervasive Interactions. DAPI 2017. Lecture Notes in Computer Science(), vol 10291. Springer, Cham. https://doi.org/10.1007/978-3-319-58697-7_32 Makhsous M, Lin F, Bankard J, Hendrix RW, Hepler M, Press J. Biomechanical effects of sitting with adjustable ischial and lumbar support on occupational low back pain: evaluation of sitting load and back muscle activity. BMC Musculoskelet Disord. 2009 Feb 5;10:17. doi: 10.1186/1471-2474-10-17. PMID: 19193245; PMCID: PMC2654542. Prommanon B, Puntumetakul R, Puengsuwan P, Chatchawan U, Kamolrat T, Rittitod
T, Yamauchi J. Effectiveness of a back care pillow as an adjuvant physical therapy for chronic non-specific low back pain treatment: a randomized controlled trial. J Phys Ther Sci. 2015 Jul;27(7):2035–8. doi: 10.1589/jpts.27.2035. Epub 2015 Jul 22. PMID: 26311921; PMCID: PMC4540812.